![]() |
JTAG-USB Programming CableSG$77.00 |
•Low-cost JTAG configuration & SPI communication solution •Connects to a standard 6-pin JTAG or SPI programming header •Works with Digilent Adept Suite & AVR Device Programmer software •Programs devices that have a JTAG voltage of 1.8V or greater [Product Details...] |
![]() |
XUP USB-JTAG Programming CableSG$207.50 |
•Compatible with Xilinx Platform Cable USB - programs all Xilinx® devices •Interfaces with 5V, 3.3V, 2.5V, 1.8V and 1.5V systems •Compatible with Full-Speed and Hi-Speed USB ports •Requires Xilinx iMPACT™ software for programming and configuration [Product Details...] |
![]() |
USB AVR Programmer with ScopeSG$26.70 |
This device is a programmer for AVR-based controllers, such as our Orangutan robot controllers and the 3pi robot. The programmer emulates an AVRISP v2 on a virtual serial port, making it compatible with standard AVR programming software. Have a TTL-level [Product Details...] |
![]() |
JTAG3-Parallel Port Programming CableSG$27.00 |
•Low-cost JTAG configuration solution •Intended for use with Digilent FPGA boards. (Not intended for use with Digilent AVR boards) •Connects directly to the parallel port of a PC, and to a standard 6-pin JTAG programming header •Can program devices tha [Product Details...] |
![]() |
JTAG HS1 Programming CableSG$25.50 |
•Small, complete, all-in-one JTAG programming solution for Xilinx FPGAs •High-Speed USB2 port can drive JTAG/SPI bus at up to 30Mbit/sec •Compatible with all Xilinx tools •Fully supported by the Adept SDK, allowing custom JTAG/SPI applications to be cr [Product Details...] |
![]() |
USB-ISS - Enhanced USB-I2C ModuleSG$37.70 |
The USB-ISS Multifunction USB Communications Module provides a complete interface between your PC and the I2C bus, SPI bus, a Serial port and general purpose Analogue Input or Digital I/O. The module is powered from the USB. Operating voltage is selectab [Product Details...] |
![]() |
USB interface for Arduino Optiboot IC (come with USB cable)SG$6.70 |
This is a general board for the USB interface. It uses the CP2102 USB to serial interface IC. The USB interface can be use with the ATmega328 w/ Arduino Optiboot IC for downloading the program. [Product Details...] |
![]() |
JTAG HS2 Programming CableSG$57.70 |
The Joint Test Action Group (JTAG)-HS2 programming cable is a high-speed programming solution for Xilinx field-programmable gate arrays (FPGAs). The cable is fully compatible will all Xilinx tools and can be seamlessly driven from iMPACT, Chipscope, and E [Product Details...] |
![]() |
CP2104 USB-to-Serial Adapter CarrierSG$6.70 |
This USB-to-serial adapter lets you easily connect a TTL serial device to a PC by acting as a virtual serial port. The board is a Micro-USB carrier for the Silicon Labs CP2104 USB-to-UART bridge that provides access to all of its control signal pins and G [Product Details...] |
![]() |
JTAG HS3 Programming CableSG$89.00 |
The JTAG HS3 is the newest member of our family of affordable high-speed Xilinx FPGA programming solutions. The HS3 builds on the successful JTAG HS1 by adding an open drain buffer to pin 14 allowing for the debugging of Xilinx Zync-SOC processors. It can [Product Details...] |